The Power Pump !
The Power Pump is an inline voltage step-up converter that accepts 9 volts DC and increases it to an output voltage of 12, 18, or 24 volts DC at specific current values (see chart below). Output voltage is determined by position of the 3-way switch located on the unit's chassis. Input is standard polarity Tip positive/Barrel negative female barrel connector and Output is standard polarity Tip negative/Barrel positive male barrel connectorSpecifications:
In: 9 VDC @ 1700 mA (recommended)
Out: 12 VDC (.65 A) - 18 VDC (.44A) -
24 VDC (.33 A) @ 5%
Power Rating: 7.83 W continuous
Polarity: Tip Negative/Barrel Positive
Directions for Use:
Attach the PP-9 directly to the PA-9 or to a lead on the Cable-5 Daisy Chain Set the PP-9 to the required voltage – It can only supply 1 voltage at a time.
Make sure you check the polarity and voltage of the unit to be powered before connecting it to the Power Pump. Connect the PP-9 to the unit (s) to be powered - You can power multiple units off each PP-9 as long as you do not exceed the max Current per voltage listed above.
You can power up to 2 PP-9's off one PA-9
Notes to User:
Godlyke, Inc. assumes no responsibility for damage resulting from abuse of misuse of this product. MAKE SURE TO CHECK THE VOLTAGE AND POLARITY BEFORE CONNECTING ANY UNIT TO THE PP-9!!!
Power-Pump is a registered trademark of Godlyke, Inc.
Patents Applied For
Waiting on POWER PUMP II Coming Nov/Dec !!
Musictoyz.com Price $XX.XX
Power All System
The Godlyke PA-9 Power-All uses digital switching technology to provide high power in an extremely compact casing with zero noise and zero heat dissipation. The PA-9's advanced circuitry "steps down" high line voltages to 9-volts and automatically supplies the required amount of current. This is the same type of technology that is used in compact power amps to provide very high wattage in a single rack space chassis. The PA-9's whopping 1.7 Amp current capability allows it to power a virtually unlimited number of 9-volt effects, including Line 6 modeling stompboxes. Other features of the PA-9 include:
* 9-volt, 1.7 Amp supply - Can power over twenty 9-volt effect pedals or similar devices (actual # of units depends on current draw of individual pedals used).
*Can replace Boss PSA-120, Boss ACA-120, and DOD PS-200R, Morley 9V, DanElectro DA-1, Dunlop ECB-03, Ibanez AC-109, Guyatone AC-2, Maxon AC210N, or just about any other 9-volt power supply.
* No transformer, thus no heat dissipation or noise (60 cycle hum)
* Takes up only one outlet socket space (unlike typical "wall wart" adaptors)
* Can run off any Mains supply (100-240v), thus no need for power transformers when travelling abroad.
* Has all necessary national safety certifications - UL, CUL, etc. (see unit for listing).
* Includes 5-connector daisy chain cable to power multiple effects units from one supply (additional cables available separately).
The Godlyke PA-9 Power-All comes complete with the following -
1 x 9-volt, 1.7 Amp power supply with 6' heavy duty power cord (industry standard tip negative/barrel positive polarity)
1 x 5-connector daisy chain cable with 12" leads between jacks (industry standard tip negative/barrel positive polarity)
2 x Reverse Polarity (tip positive/barrel negative) Barrel connector Jumper cords (red) - For use w/older Dunlop, certain Fulltone, etc.
2 x Battery plug (reverse polarity) Jumper cords (grey) - For use w/older effects and new boutique units that lack DC jacks (older Ibanez, older MXR, Z-Vex, etc.) - connects directly onto pedal's battery clip.
2 x 1/8" Phone Plug (Tip Positive/sleeve negative) Jumper cords (blue) - for use w/old DOD, Pro Co Rat, certain EH, etc.
1 x Standard Polarity (tip negative/barrel positive) Barrel connector Jumper cord (Black) - Extension cord for use w/larger, irregular sized units.
1 x Reverse Polarity (Tip Positive/Barrel negative) Barrel Connector Jumper cord (Green) - for use w/Line 6 modelers, etc. Male Barrel plug has larger internal diameter.
Top of Page |
musictoyz.com HOME